model_icon
(13-07) Non Tempered (Neither heated or cooled) Make-Up Air - Low Cost Make Up Air - (5,000 - 30,000 CFM)
LEV-CO’s Non-Tempered Air Make-Up Systems replaces exhausted air more efficiently and with more comfort than conventional Air Make-Up air systems. Ideal for production facilities that generate heat, for example welding shops where welding processes generate up to 450,000 BTU per hour per welder.
Non-Tempered units are grouped into 2 different types:
  • 100% Outdoor Air: These units draw outside air and consist of a simple Axial fan, motorized inlet damper, Insulated cabinet and flow straightener.
  • Modulating units – 0-100% Outdoor air: these units draw a variable amount of outside air from outside and when the internal temperature drops below the customer’s set point (EG: 70 degrees F) the THERMOSTAT controlled modulating air-mixing system allows air to be drawn from OUTSIDE or INSIDE in order to maintain desired indoor temperature. This solution is most often selected when the production level cannot be guaranteed or additional heat sources are not available.
Both solutions are aided by custom engineered flame retardant fabric distribution ducting, where we able to take advantage of the STRATIFIED heat in ceiling, creating the equivalent of lowering a conventional thermostat by ½ degree F per foot of ceiling height or provide MAKE-UP without additional heat.
This is accomplished by discharging the air in HIGH velocity air jets as close to the ceiling as possible. The result of the mixing is that the fresh air is heated to room temperature very quickly before it reaches the lower occupied area. This is extremely effective in welding shops where each welder can generate as much as 450,000 BTU per hour in heat.
This “De-Stratifying” air distribution method has the added benefit of diluting and cooling any “Fugitive emissions/smoke” in the ceiling space and allows this air to be drawn down to floor level where it can be filtered and or exhausted by local exhaust ventilation systems.
When no fresh air is needed, the system can be shut down and the outside air dampers will close automatically or the system can be run on one hundred percent (100%) re-circulated air.
Conversely, if cooling air is required, “Bi-Flex” ducting can be selected (Optional). Bi-Flex ducting allows the air to continue to be exhausted into the ceiling space in the winter months AND then be re-directed downwards to the workers in summer months. This method leaves the bulk of the hot air in the ceiling space and places high velocity cooling air towards the worker. (The velocity shall not be high enough to disturb welding gases/processes).

Product Function:

LEV-CO’s Non-Tempered Air Make-Up Systems replaces exhausted air more efficiently and with more comfort than conventional Air Make-Up air systems. Ideal for production facilities that generate heat, for example welding shops where welding processes generate up to 450,000 BTU per hour per welder.
Non-Tempered units are grouped into 2 different types:
  • 100% Outdoor Air: These units draw outside air and consist of a simple Axial fan, motorized inlet damper, Insulated cabinet and flow straightener.
  • Modulating units – 0-100% Outdoor air: these units draw a variable amount of outside air from outside and when the internal temperature drops below the customer’s set point (EG: 70 degrees F) the THERMOSTAT controlled modulating air-mixing system allows air to be drawn from OUTSIDE or INSIDE in order to maintain desired indoor temperature. This solution is most often selected when the production level cannot be guaranteed or additional heat sources are not available.
Both solutions are aided by custom engineered flame retardant fabric distribution ducting, where we able to take advantage of the STRATIFIED heat in ceiling, creating the equivalent of lowering a conventional thermostat by ½ degree F per foot of ceiling height or provide MAKE-UP without additional heat.
This is accomplished by discharging the air in HIGH velocity air jets as close to the ceiling as possible. The result of the mixing is that the fresh air is heated to room temperature very quickly before it reaches the lower occupied area. This is extremely effective in welding shops where each welder can generate as much as 450,000 BTU per hour in heat.
This “De-Stratifying” air distribution method has the added benefit of diluting and cooling any “Fugitive emissions/smoke” in the ceiling space and allows this air to be drawn down to floor level where it can be filtered and or exhausted by local exhaust ventilation systems.
When no fresh air is needed, the system can be shut down and the outside air dampers will close automatically or the system can be run on one hundred percent (100%) re-circulated air.
Conversely, if cooling air is required, “Bi-Flex” ducting can be selected (Optional). Bi-Flex ducting allows the air to continue to be exhausted into the ceiling space in the winter months AND then be re-directed downwards to the workers in summer months. This method leaves the bulk of the hot air in the ceiling space and places high velocity cooling air towards the worker. (The velocity shall not be high enough to disturb welding gases/processes).

Construction:

Frequently bought together these options:

Part #
Qty 
Description
MJET-24-JSNM
5,000 CFM @ 1.3" SP Unfired, Non-Modulating MUA unit, 3 HP TEFC Motor. Unit comes c/w motorized dampers and flow straightener
MJET-30-JSNM
Air Make-up System - Non-Modulation
MJET-36-JSNM
Air Make-up System - Non-Modulation
MJET-42-JSNM
Air Make-up System - Non-Modulation
MJET-48-JSNM
Air Make-up System - Non-Modulation
MJET-54-JSNM
Air Make-up System - Non-Modulation: - Jet Stream unit (Non Modulating), insulated cabinet, 36,000 CFM, .5 Static Pressure, 7.5hp motor, controls
MJET-60-JSNM
Air Make-up System - Non-Modulation
Part #
Qty 
Description
MJET-24-JSAM
5000 CFM @ 1.3" SP Unfired MUA unit w/ Recirculation 3 HP TEFC Motor. Unit comes c/w motorized dampers, temperature control, insulated cabinet and flow straightener
MJET-30-JSAM
10,000 CFM @ 1.3" SP Unfired MUA unit w/ Recirculation 5 HP TEFC Motor. Unit comes c/w motorized dampers, temperature control, insulated cabinet and flow straightener
MJET-36-JSAM
15,000 CFM @ 1.3" SP Unfired MUA unit w/ Recirculation 7.5 HP TEFC Motor. Unit comes c/w motorized dampers, temperature control, insulated cabinet and flow straightener
MJET-42-JSAM
20,000 CFM @ 1.3" SP Unfired MUA unit w/ Recirculation 7.5 HP TEFC Motor. Unit comes c/w motorized dampers, temperature control, insulated cabinet and flow straightener
MJET-48-JSAM
25,000 CFM @ 1.3" SP Unfired MUA unit w/ Recirculation 10 HP TEFC Motor. Unit comes c/w motorized dampers, temperature control, insulated cabinet and flow straightener
MJET-54-JSAM-1
30,000 CFM @ 1.3" SP Unfired MUA unit w/ Recirculation 3 HP TEFC Motor. Unit comes c/w motorized dampers, temperature control, insulated cabinet and flow straightener
MJET-54-JSAM-2
37,000 CFM @ 1.3" SP Unfired MUA unit w/ Recirculation 20 HP TEFC Motor. Unit comes c/w motorized dampers, temperature control, insulated cabinet and flow straightener
MJET-60-JSAM-1
40,000 CFM @ 1.3" SP Unfired MUA unit w/ Recirculation 20 HP TEFC Motor. Unit comes c/w motorized dampers, temperature control, insulated cabinet and flow straightener
MJET-60-JSAM-2
50,000 CFM @ 1.3" SP Unfired MUA unit w/ Recirculation 25 HP TEFC Motor. Unit comes c/w motorized dampers, temperature control, insulated cabinet and flow straightener
Part #
Qty 
Description
M-MTR-.75HP-3600-C-56-5/8-575/3/60-EXP
.75HP Explosion Proof Motor 575/6/60 V 3600 RPM, C/W 56 or 143 C flange and a 5/8 shaft size. *CSA Approved Motor*
M-MTR-0.5HP-3600-B5-71-14-115-230/1/60
Motor 0.5HP 3600 RPM B5 Flange 115/230V, 14 Shaft size, 71 Frame. *CSA Approved Motor*
M-MTR-0.5HP-3600-B5-71-14-208-230-460/3/60
Motor 0.5HP 3600 RPM B5 Flange 208/230V, 14 Shaft size, 71 Frame. *CSA Approved Motor*
M-MTR-0.5HP-3600-B5-71-14-575/3/60
Motor 0.5HP 3600 RPM B5 Flange 575V, 14 Shaft size, 71 Frame. *CSA Approved Motor*
M-MTR-0.75HP-3600-B5-71-14-115-230/1/60
Motor 0.75HP 3600 RPM B5 Flange 115/230V, 14 Shaft size, 71 Frame. *CSA Approved Motor*
M-MTR-0.75HP-3600-B5-71-14-208-230-460/3/60
Motor 0.75HP 3600 RPM B5 Flange 208/230/460V, 14 Shaft size, 71 Frame. *CSA Approved Motor*
M-MTR-0.75HP-3600-B5-71-14-575/3/60
Motor 0.75HP 3600 RPM B5 Flange 575V, 14 Shaft size, 71 Frame.*CSA Approved Motor*
M-MTR-1.5HP-3600-575/3
Motor for MP14, 1.5HP, 145T, 5/8" shaft, 575V, 3PH, 3450 RPM, TEFC. *CSA Approved Motor*
M-MTR-1.5HP-3600-B5-80-19-575/3/60
Motor 1.5HP 3600 RPM B5 Flange 575V, 19 Shaft size, 80 Frame 1.1kw. *CSA Approved Motor*
M-MTR-1.5HP-3600-B5-90-19-208-230-460/3/60
Motor 1.5HP 3600 RPM B5 Flange 208/230/460V, 19 Shaft size, 90 Frame. *CSA Approved Motor*
M-MTR-1.5HP-3600-C-143-5/8-575-EXP
1.5 HP Explosion Proof Motor 575 V 3600 RPM, C/W 143 C flange and a 5/8 shaft size. *CSA Approved Motor*
M-MTR-1.5HP-3600-C-56-115-230-EXP
1.5 HP Explosion Proof Motor 120 V 3600 RPM, C/W 56 or 143 C flange and a 5/8 shaft size
  • WITHOUT OVERLOAD PROECTION *CSA Approved Motor*
  • M-MTR-1.5HP-3600-C-56-5/8-115-230-EXP
    1.5 HP Explosion Proof Motor 120 V 3600 RPM, C/W 56 or 143 C flange and a 5/8" shaft size.*CSA Approved Motor*
    M-MTR-1.5HP-3600-C-56-5/8-208-460-EXP
    1.5 HP Explosion Proof Motor 208-460 V 3600 RPM, C/W 56 or 143 C flange and a 5/8 shaft size. *CSA Approved Motor*
    M-MTR-1.5HP-3600-C-56-5-1/2-115-230/1/60
    Motor 1.5 hp 3400 rpm C flange mount 115-230 volt/single phase 60 hz.*CSA Approved Motor*
    M-MTR-1.5HP-575/3/60-EXP
    1.5HP Explosion proof 575/3/60 Class I / Div. 1 Grp. C,D,F & G - 3600 RPM, 143TC FRAME 7/8'' SHAFT. *CSA Approved Motor*
    M-MTR-10HP-3600-B5-132-38-575/3/60
    Motor 10HP 3600 RPM B5 Flange 575V, 38 Shaft size, 132 Frame 7.5kw. *CSA Approved Motor*
    M-MTR-15HP-3600-254T-1 1/8-575-EXP
    15 HP Explosion Proof Motor 575 V 3600 RPM, 254T Frame and a 1 1/8 shaft size. *CSA Approved Motor*
    M-MTR-1HP-3600-C-56-3600-115-230-EXP
    1 HP Explosion Proof Motor 120 V 3600 RPM, C/W 56 C flange and a 5/8 shaft size
  • WITHOUT OVERLOAD PROECTION. *CSA Approved Motor*
  • M-MTR-1HP-3600-C-56-3600-115-230-EXP
    1 HP Explosion Proof Motor 120 V 3600 RPM, C/W 56 C flange and a 5/8" shaft size
  • WITHOUT OVERLOAD PROECTION. *CSA Approved Motor*
  • M-MTR-1HP-3600-C-56-5/8-115-230-EXP
    1 HP Explosion Proof Motor 120 V 3600 RPM, C/W 56 or 143 C flange and a 5/8 shaft size
  • WITHOUT OVERLOAD PROECTION. *CSA Approved Motor*
  • M-MTR-1HP-3600-C-56-5/8-115-230-EXP
    1 HP Explosion Proof Motor 120 V 3600 RPM, C/W 56 or 143 C flange and a 5/8 shaft size
  • WITHOUT OVERLOAD PROECTION. *CSA Approved Motor*
  • M-MTR-1HP-3600-C-56-5/8-230-460-EXP
    1 HP Explosion Proof Motor 230-460 V 3600 RPM, C/W 56 or 143 C flange and a 5/8 shaft size. *CSA Approved Motor*
    M-MTR-20HP-3600-254T-1 1/8-575-EXP
    20 HP Explosion Proof Motor 575 V 3600 RPM, 254T Frame and a 1 1/8 shaft size. *CSA Approved Motor*
    M-MTR-20HP-3600-B5-160-42-575/3/60
    Motor 20HP 3600 RPM B5 Flange 575V, 42 Shaft size, 160 Frame. *CSA Approved Motor*
    M-MTR-2HP-1800-B5-90-24-115-230/1/60
    Motor 2HP 1800 RPM B5 Flange 115/230V, 24 Shaft size, 90 Frame. *CSA Approved Motor*
    M-MTR-2HP-1800-B5-90-24-208-230-460/3/60
    Motor 2HP 3600 RPM B5 Flange 208-240-460V, 24 Shaft size, 90 Frame. *CSA Approved Motor*
    M-MTR-2HP-3600-B5-90-24-575/3/60
    Motor 2HP 3600 RPM B5 Flange 575V, 24 Shaft size, 90 Frame 1.5kw. *CSA Approved Motor*
    M-MTR-2HP-3600-C-145-7/8-575-EXP
    2 HP Explosion Proof Motor 575 V 3600 RPM, C/W 145 TC flange and a 1 1/8 shaft size. *CSA Approved Motor*
    M-MTR-2HP-3600-C-56-5/8-115-230-EXP
    2 HP Explosion Proof Motor 115-230 V 3600 RPM, C/W 56 or 143 C flange and a 5/8 shaft size
  • WITHOUT OVERLOAD PROECTION. *CSA Approved Motor*
  • M-MTR-2HP-3600-C-56-5/8-208-460-EXP
    2 HP Explosion Proof Motor 208-460 V 3600 RPM, C/W 56 or 143 C flange and a 5/8 shaft size. *CSA Approved Motor*
    M-MTR-2HP-3600-C-56-5/8-575-EXP
    Explosion Proof Motor 2 HP 3600 RPM C flange mount 575/3/60 TEFC 56 C Frame. *CSA Approved Motor*
    M-MTR-3HP-208-230/1/60-EXP-CLS1-GRPC&D
    Explosion proof 3HP 208-230/1/60 Class I / Div. 1 Grp. C&D and Class II/ Div. 1 Grp. F&G. 3450 RPM, NO FLANGE
  • WITHOUT OVERLOAD PROECTION. *CSA Approved Motor*
  • M-MTR-3HP-208-230/3/60-EXP-CLS1-GRPC&D
    Explosion proof 3HP 208-230/3/60 Class I / Div. 1 Grp. C&D and Class II/ Div. 1 Grp. F&G. 3450 RPM, NO FLANGE. *CSA Approved Motor*
    M-MTR-3HP-3600-B5-90-24-115-230/1/60
    Motor 3HP 3600 RPM B5 Flange 115/230V, 24 Shaft size, 90 Frame. *CSA Approved Motor*
    M-MTR-3HP-3600-B5-90-24-208-230-460/3/60
    Motor 3HP 3600 RPM B5 Flange 208/230/460V, 24 Shaft size, 90 Frame. *CSA Approved Motor*
    M-MTR-3HP-3600-B5-90-24-575/3/60
    Motor 3HP 3600 RPM B5 Flange 575V, 24 Shaft size, 90 Frame 2.2kw. *CSA Approved Motor*
    M-MTR-3HP-3600-C-182-1 1/8-230-460
    3 HP MOTOR 230-460V 3600 RPM, 182T C flange, 1 1/8 shaft size and feet. *CSA Approved Motor*
    M-MTR-3HP-3600-C-182-1 1/8-575
    3 HP MOTOR 575V 3600 RPM, 182T C flange, 1 1/8 shaft size and feet. *CSA Approved Motor*
    M-MTR-3HP-3600-NF-145- 7/8-208-460
    3 HP MOTOR 208/460 V 3600 RPM, 145T NO flange and a 7/8 shaft size. *CSA Approved Motor*
    M-MTR-3HP-3600-NF-145- 7/8-575
    3 HP MOTOR 575/3/60 V 3600 RPM, 145T NO flange and a 7/8 shaft size. *CSA Approved Motor*
    M-MTR-3HP-3600-NF-182-1 1/8-115-230
    3 HP MOTOR 115/230V 3600 RPM, KX182T NO flange and a 1 1/8 shaft size
  • WITHOUT OVERLOAD PROECTION. *CSA Approved Motor*
  • M-MTR-3HP-3600-NF-182-1 1/8-230-460
    3 HP MOTOR 230/460V 3600 RPM, 182T NO flange and a 1 1/8 shaft size. *CSA Approved Motor*
    M-MTR-4HP-3600-B5-100-1-230-460
    Metric Motor 4 HP 3600 RPM B5 flange 230/460V, 25mm Shaft size, 100L Frame. *CSA Approved Motor*
    M-MTR-4HP-3600-B5-100-28-208-230-460/3/60
    Motor 4HP 3600 RPM B5 Flange 208/230/460V, 28 Shaft size, 100 Frame.*CSA Approved Motor*
    M-MTR-4HP-3600-B5-100-28-575/3/60
    Motor 4HP 3600 RPM B5 Flange 575V, 28 Shaft size, 100 Frame 3kw. *CSA Approved Motor*
    M-MTR-4HP-3600-B5-100-575
    Metric Motor 4 HP 3600 RPM B5 flange mount 575/3/60 TEFC 100L Shaft size 25mm. *CSA Approved Motor*
    M-MTR-4HP-3600-B5-100L-25MM-575
    Metric Motor 4 HP 3600 RPM B5 flange mount 575/3/60 TEFC 100L Frame c/w feet. *CSA Approved Motor*
    M-MTR-4HP-3600-B6-100-25-230-460
    Metric Motor 4 HP 3600 RPM B6 flange 230/460V, 25mm Shaft size, 100L Frame. *CSA Approved Motor*
    M-MTR-5HP-3450-184T-3ph-TEFC-575
    5HP,184T,3450RPM,3PHASE,TEFC. *CSA Approved Motor*
    M-MTR-5HP-3600-B5-112-28-208-230-460/3/60
    Motor 5HP 3600 RPM B5 Flange 208/230/460V, 28 Shaft size, 112 Frame. *CSA Approved Motor*
    M-MTR-5HP-3600-B5-112-28-575/3/60
    Motor 5HP 3600 RPM B5 Flange 575V, 28 Shaft size, 112 Frame 3.7kw. *CSA Approved Motor*
    M-MTR-5HP-3600-NF-184T-1 1/8-575-EXP
    5 HP explosion Proof Motor, 3600 RPM NO flange, 575/3/60V, 184T Frame, 1 1/8 Shaft Size. *CSA Approved Motor*
    M-MTR-7.5HP-3600-B5-132-38-208-230-460/3/60
    Motor 7.5HP 3600 RPM B5 Flange 208/230/460V, 38 Shaft size, 132 Frame. *CSA Approved Motor*
    M-MTR-7.5HP-3600-B5-132-38-575/3/60
    Metric Motor 7.5HP 3600 RPM B5 Flange 575V, 38 Shaft size, 132 Frame 5.5kw. *CSA Approved Motor*
    M-MTR-LFan
    Motor for Leader Fan. *CSA Approved Motor*
    M-MTR-RB-80-6bU
    Regenerative Motor Blower 7.5 HP, 3/60/575V.
  • 175 CFM @ 100 SP
  • Integral inlet and outlet silencers.
  • Precision cast aluminum impeller.
  • 2.5 ” NPT inlet and outlet connections.
  • 3/60/575V, 6.3 kW, 3450 RPM, IP54 rated motor complete with CSA (Canada & US) certification for use in all US states and Canadian provinces. *CSA Approved Motor*
  • M-MTR-RGB-150-90
    Regenerative Motor Blower 5 HP, 3/60/575V.
  • 150 CFM @ 90 SP
  • Integral inlet and outlet silencers.
  • Precision cast aluminum impeller.
  • 2.5 ” NPT inlet and outlet connections.
  • 3/60/575V, 5 HP, 3450 RPM, IP54 rated motor complete with CSA (Canada & US) certification for use in all US states and Canadian provinces. *CSA Approved Motor*
  • M-MTR-RGB-175-100
    Regenerative Motor Blower 7.5 HP, 3/60/575V.
  • 175 CFM @ 100 SP
  • Integral inlet and outlet silencers.
  • Precision cast aluminum impeller.
  • 2.5 ” NPT inlet and outlet connections.
  • 3/60/575V, 6.3 kW, 3450 RPM, IP54 rated motor complete with CSA (Canada & US) certification for use in all US states and Canadian provinces. *CSA Approved Motor*
  • M-MTR-RGB-390-100
    Regenerative Motor Blower 15 HP, 3/60/575V.
  • 390 CFM @ 100 SP
  • Integral inlet and outlet silencers.
  • Precision cast aluminum impeller.
  • 3.5 ” NPT inlet and outlet connections.
  • 3/60/575V, 12.5 kW, 3450 RPM, IP54 rated motor complete with CSA (Canada & US) certification for use in all US states and Canadian provinces. *CSA Approved Motor*
  • N-MTR-0.5HP-1800-C-56-1/2-115-230
    NEMA Motor 0.5 HP, 1800 RPM, C flange, 115/230 , 56 Frame, Shaft size 5/8"
  • WITHOUT OVERLOAD PROTECTION. *CSA Approved Motor*
  • N-MTR-0.5HP-1800-C-56-1/2-115-230-EXP
    NEMA Motor 0.5 HP, 1800 RPM, C flange, 115/230 , 56 Frame, Shaft size 5/8"
  • WITHOUT OVERLOAD PROTECTION
  • Explosion proof. *CSA Approved Motor*
  • N-MTR-0.5HP-3600-B5-71-115/230
    NEMA Motor 0.5HP, 3600RPM, B5 flange, 208/230V, N/A Frame,14mm Shaft size. *CSA Approved Motor*
    N-MTR-0.5HP-3600-C-56-1/2-115-230
    NEMA Motor 0.5 HP, 3600 RPM, C flange, 115/230 , 56 Frame, Shaft size 5/8
  • WITHOUT OVERLOAD PROTECTION. *CSA Approved Motor*
  • N-MTR-0.5HP-3600-C-56-1/2-230-460
    NEMA Motor 0.5 HP, 3600 RPM, C flange, 230/460 V TEFC, 56 Frame, 5/8 Shaft size.*CSA Approved Motor*
    N-MTR-0.5HP-3600-C-56-1/2-575
    NEMA Motor 0.5 HP, 3600 RPM, C flange, 575/3/60, 56 Frame 5/8" Shaft size
    N-MTR-0.75HP-3600-C-56-5/8-115
    NEMA Motor 0.75 HP, 3600 RPM, C flange, 115 V, D56 Frame, 5/8 Shaft Size
  • WITHOUT OVERLOAD PROECTION. *CSA Approved Motor*
  • N-MTR-0.75HP-3600-C-56-5/8-115-230
    NEMA Motor 0.75 HP, 3600 RPM, C flange, 115/230 56 Frame, 5/8" Shaft Size
  • WITHOUT OVERLOAD PROECTION
  • N-MTR-0.75HP-3600-C-56-5/8-230-460
    NEMA Motor 0.75 HP, 3600 RPM, C flange, 230-460, 56 Frame, Shaft size 5/8. *CSA Approved Motor*
    N-MTR-0.75HP-3600-C-56-5/8-575
    NEMA Motor 0.75 HP, 3600 RPM, C flange, 575/3/60 V, 56 Frame, Shaft size 5/8. *CSA Approved Motor*
    N-MTR-0.75HP-3600-NF-56-5/8-115-230
    NEMA Motor 0.75 HP, 3600 RPM, No flange, 115/230 V, 56Z Frame, 5/8 Shaft Size
  • WITHOUT OVERLOAD PROECTION. *CSA Approved Motor*
  • N-MTR-1.5HP-1800-56-5/8-575/3/60
    NEMA Motor 1.5 hp 1800 rpm w/feet 575 volt/3 phase 60 hz TEFC 56. *CSA Approved Motor*
    N-MTR-1.5HP-1800-C-56-5/8-115-230/1/60
    NEMA Motor 1.5 hp 1800 rpm C flange mount 115-230 volt/single phase 60 hz TEFC 56 C Frame flange
  • WITHOUT OVERLOAD PROECTION Load 100%, - efficiency is 90%, 2080 hours/year and 0.11$/kW/h. *CSA Approved Motor*
  • N-MTR-1.5HP-1800-C-56-5/8-575/3/60
    NEMA Motor 1.5 hp 1800 rpm C flange mount 575 volt/single phase 60 hz TEFC 56 C Frame flange.*CSA Approved Motor*
    N-MTR-1.5HP-3600-C-143-7/8-115
    NEMA Motor 1.5HP, 3600 RPM, C flange, V115, F143T Frame, Shaft Size 7/8
  • WITHOUT OVERLOAD PROECTION. *CSA Approved Motor*
  • N-MTR-1.5HP-3600-C-143-7/8-115-230/1/60
    NEMA Motor 1.5 hp 3600 rpm C flange mount 115-230 volt/single phase 60 hz TEFC 143 C Frame flange
  • WITHOUT OVERLOAD PROECTION Load 100%, - efficiency is 90%, 2080 hours/year and 0.11$/kW/h. *CSA Approved Motor*
  • N-MTR-1.5HP-3600-C-143-7/8-575
    NEMA Motor 1.5 HP, 3600 RPM, C flange, V575/3/60, F143T Frame, Shaft Size 7/8. *CSA Approved Motor*
    N-MTR-1.5HP-3600-C-56-5/8-115-230/1/60
    NEMA Motor 1.5 hp 3600 rpm C flange mount 115-230 volt/single phase 60 hz TEFC 56 C Frame flange
  • WITHOUT OVERLOAD PROTECTION Load 100%, - efficiency is 90%, 2080 hours/year and 0.11$/kW/h.*CSA Approved Motor*
  • N-MTR-1.5HP-3600-C-56-5/8-115-230-D
    NEMA Motor 1.5HP, 3600 RPM, C flange, V115/230, 56 Frame, Shaft Size 5/8 Demo
  • WITHOUT OVERLOAD PROECTION. *CSA Approved Motor*
  • N-MTR-1.5HP-3600-C-56-5/8-208-460
    NEMA Motor 1.5 HP 3600 RPM C flange mount 208-230/460/60 TEFC 56 C Frame. *CSA Approved Motor*
    N-MTR-1.5HP-3600-C-56-5/8-208-460
    NEMA Motor 1.5 HP 3600 RPM C flange mount 208-230/460/60 TEFC 56 C Frame. *CSA Approved Motor*
    N-MTR-1.5HP-3600-C-56-5/8-575
    NEMA Motor 1.5 hp 3600 rpm C flange 575/3/60 volt,Shaft Size 5/8", 56 Frame
    N-MTR-1.5HP-3600-NF-56-5/8-115-230
    NEMA Motor 1.5HP, 3600 RPM, NO flange, V115/230, 56H Frame, Shaft Size 5/8
  • WITHOUT OVERLOAD PROECTION. *CSA Approved Motor*
  • N-MTR-3HP-3600-C-145-7/8-575-EXP
    3 HP Explosion Proof Motor 575 V 3600 RPM, C/W 145 TC flange and a 7/8 shaft size. Motor is rated at Class 1/ Division 1 Group C & D and Class 2/ division 1 Group F & G. *CSA Approved Motor*
    N-MTR-7.5HP-3600-C-213-1 3/8-575
    Motor 7.5HP 36000 RPM C Flange 575V, 1 3/8" Shaft size, 213T Frame.*CSA Approved Motor*
    Part #
    Qty 
    Description
    MJET-24-FDCT
    Fabric Duct with custom hole pattern
    MJET-30-FDCT
    Fabric Duct with custom hole pattern, 30"
    MJET-36-FDCT
    Fabric Duct with custom hole pattern
    MJET-42-FDCT
    Fabric Duct with custom hole pattern
  • Complete with all Hardware and cable (NB: Cable to be 10% longer than fabric duct)
  • MJET-48-FDCT
    Fabric Duct with custom hole pattern
    MJET-54-FDCT
    Fabric Duct with custom hole pattern
    MJET-60-FDCT
    Fabric Duct with custom hole pattern
    Part #
    Qty 
    Description
    PG-10
    Pressure Gauge - complete with Wall, Ceiling or table mounting bracket and 0-10 pressure gauge. 3/16 inside diameter tubing ordered separately.
    Technical Info Requested
    To make sure that you are a human being and not a robot, please also enter the letters you see below: